Lovejoy UFH-75S Flange-to-Shaft Uniflex Coupling

68514413868, UFH Type without Keyway, Regular & Short Version – Inch

Dimensional Data

Bore Size	1/2 in
Hub Size	UFH75S
Set Screw Thread Size (Dimension T)	1/4-20
Keyway Size (W x D)	No Keyway
Dimension HD	1.420 in36.07 mm
Overall Length	2.000 in50.80 mm
Pin Size	0.125 in
Pin Location (Dimension SL)	0.41 in
Length thru Bore	0.840 in21.34 mm
Min. Bore (Dimensions ID1/ID2)	0.375 in9.53 mm
Max. Bore (Dimensions ID1/ID2)	0.750 in19.00 mm
Dimension BC	2.000 in50.80 mm
Dimension D	2.880 in73.15 mm
Flange Diameter (Dimension FD)	2.500 in63.50 mm
Dimension FL	0.380 in9.65 mm
Mounting Screw Thread Size	1/4-20
Cubic inches	12.50000 in³

Performance Data

Operating Temperature Range	-40 to 250 ºF
Nominal Torque	175 in·lb
Rated Torque for 1.0 Service Factor	175.00 in·lb
Max. Speed	20000.00 rpm
Max. Recommended End Play	0.020 in0.51 mm
Max. Parallel Offset	0.019 in0.48 mm
Wind-Up Angle at Nominal Torque	1.12 º
Wind-Up Angle at Max. Torque	3.00 º
Rated HP at 100 rpm	0.28 hp
# of Set Screws Required	1

Coupling Design

Coupling Design

Flexible Spring Type Coupling with Exclusive Triple Wound Spring Design The Uniflex Coupling is an all steel, single piece coupling that solves a variety of application concerns including: high misalignment, space limitations, high temperature, and exceptionally low backlash/windup. The unique flexing center of the Uniflex consists of three opposingly wound square wire springs for forward or reverse operation. Two steel hubs are then brazed to the steel spring pack to create a durable one-piece flexible coupling.

Notes

Notes

Total backlash is approximately 1/3 of windup at maximum torque – consult Lovejoy Engineering for more information. OAL & Dimension FL Tolerance + .12 inch. Mounting screws not supplied.

 

Lovejoy UFH-75S Flange-to-Shaft Uniflex Coupling

 

This Lovejoy UFH-75S Uniflex coupling is a short, all-steel, single-piece coupling with a 1/2″ rounded bore that connects flange mounted equipment to a shaft. The flexing center of the coupling consists of three opposingly wound square wire springs for forward or reverse operation, providing low backlash/windup.

Its compact, single-piece design allows for placement in tight places, and its all-metal design is durable and requires no lubrication. This coupling is resistant to oil, grease, dirt, and most industrial chemicals and can withstand temperatures ranging from -40 to 450 degrees F.

A set screw secures the coupling into position on the shaft. This coupling has a 2.5″ flange diameter and a length of 2″. It can handle up to 175 in-lbs maximum torque and a speed of 20,000 RPM.

This coupling is suitable for applications such as printing and binding registration, robotics/positioning, conveyors, machine tools, centrifugal pumps, agricultural machinery, blowers, winding machines, and steering mechanisms.

Flexible couplings are used to link two rotating shafts that are not aligned in order to transmit the rotational power, known as torque, from one shaft to the other. Most flexible couplings consist of two hubs and a middle assembly; each hub attaches to a shaft while the middle assembly flexes between the hubs to accommodate the misalignment of the two shafts.

Shaft misalignments are generally either parallel or angular and cause complications to transmitting rotational power from one shaft to another in the form of stresses, loads, vibrations, and other forces, which vary from one type of misalignment to another.

Flexible couplings are used in a broad range of applications, such as in motor vehicles, conveyors, escalators, agricultural, forestry and mining equipment, aeronautics, robotics and space exploration, among others.

Lovejoy manufactures flexible couplings, universal joints, variable speed drives, and other transmission and mechanical power products. The company, founded in 1900, is headquartered in Downers Grove, IL.

Lovejoy UFH-75S Flange-to-Shaft Uniflex Coupling

Asin	B004S2TAT8